300-420復習解答例,300-420日本語問題集,300-420無料問題,300-420日本語対策問題集,300-420技術問題

親愛なる受験生の皆様、何かCiscoの300-420試験のトレーニング授業に加入したいのですか。実は措置を取ったら一回で試験に合格することができます。JpexamのCiscoの300-420試験のトレーニング資料はとても良い選択なんですよ。Jpexamの仮想ネットワークトレーニングと授業は大量の問題集に含まれていますから、ぜひあなたが気楽に試験に合格することを約束します。

シスコの300-420試験は、エンタープライズネットワークの設計においてキャリアアップを望むITプロフェッショナルにとって重要な認定試験です。試験は、シスコ技術を使用した高度なエンタープライズネットワークアーキテクチャの設計と実装に関する知識とスキルを試します。この認定プログラムは、世界的に認知されており、エンタープライズネットワーク設計の最新動向とベストプラクティスについての情報を提供することで、プロフェッショナルが最新の情報を把握し続けることを支援しています。試験に合格することは、候補者の知識とスキルの正当性を証明するものであり、CCNP Enterprise認定の前提条件となります。

試験300-420復習解答例 & 合格スムーズ300-420日本語問題集 | 大人気300-420無料問題

Jpexamの300-420資料を言及するたびに、多くの人の反応は高い出題率です。Cisco認証に参加する人が不安の状態から平静になって、試験に順調に合格しました。新しい資料がないなら、努力だけが不足です。300-420試験に合格したいなら、我々の全面的な資料を参考として試験を準備しましょう。

Cisco Designing Cisco Enterprise Networks 認定 300-420 試験問題 (Q52-Q57):

質問 # 52
Refer to the exhibit. An engineer is designing a Layer 2 campus network. The design must support fast convergence and leverage as much bandwidth as possible between layers.
Distribution switches do support VSS; unfortunately, not all routing protocols are available for use due to license limitations. Which solution must the engineer choose?

* A. EtherChannel
* B. RSTP
* C. ECMP
* D. MEC
正解：D

解説：
Configure StackWise Virtual on distribution layer and then configure MEC.
https://www.cisco.com/c/en/us/products/collateral/switches/catalyst-9000/nb-06-cat-9k-stack-wp- cte-en.html

質問 # 53
A large chain of stores currently uses MPLS-based T1 lines to connect their stores to their data center. An architect must design a new solution to improve availability and reduce costs while keeping these considerations in mind:
* The company uses multicast to deliver training to the stores.
* The company uses dynamic routing protocols and has implemented QoS.
* To simplify deployments, tunnels should be created dynamically on the hub when additional stores open.
Which solution should be included in this design?

* A. IPsec
* B. VPLS
* C. GET VPN
* D. DMVPN
正解：D

質問 # 54
Refer to the exhibit. An engineer is designing a routing solution for a customer. The design must ensure that a failure of network 10.1.0.0/24, 10.1.2.0/24, 10.2.1.0/24, or 10.2.3.0/24 does not impact the core. It also requires fast convergence time during any link failover in the core or access networks.
Which solution must the engineer select?

* A. Add aggregation layer between core and access networks.
* B. Enable summarization on routers A and C.
* C. Enable FRR for the connected networks of routers A and C.
* D. Enable graceful restart on routers A and C.
正解：C

質問 # 55
An engineer is tasked with designing a dual BGP peering solution with a service provider. The design must meet these conditions:
* The routers will not learn any prefix with a subnet mask greater than /24.
* The routers will determine the routes to include in the routing table based on the length of the mask alone.
* The routers will make this selection regardless of the service provider configuration.
Which solution should the engineer include in the design?

* A. Use a route map and access list to block the desired networks, and apply the route map to BGP neighbors inbound.
* B. Use a route map and prefix list to block the desired networks, and apply the route map to BGP neighbors outbound.
* C. Use an IP prefix list to block the desired networks and apply the IP prefix list to BGP neighbors inbound.
* D. Use an IP prefix list to block the desired networks and apply the IP prefix list to BGP neighbors outbound.
正解：C

質問 # 56
An engineer uses Postman and YANG to configure a router with:
- OSPF process ID 200
- network 172.16.10.128/26 enabled for Area 0
Which get-config reply verifies that the model set was designed correctly?

* A.